Epsolar LS0512R Manuel d'instructions Page 1

LS0512R —— Solar Light Controller Please read this manual carefully before using the product！ EPSOLAR INSTRUCTION MANUAL

6 4 –Setting button Set load work mode (in manual mode used for load ON/OFF). 5 –Solar Module Terminals Connect solar modules. 6 –Battery Terminals

7 3 Installation Instructions 3.1 Mounting Read through the entire installation section first before beginning installation. Be very careful whe

8 NOTE: When mounting the controller, ensure free air through the controller heat sink fins. There should be at least 6 inches (150 mm) of clearance a

9 Figure 3-1 Mounting and cooling Step 3: Mark Holes Use a pencil or pen to mark the four (4) mounting hole locations on the mounting surfa

10 3.2 Wiring NOTE: A recommended connection order has been provided for maximum safety during installation. NOTE: The controller is a common posi

11 Before battery is connected, make sure that battery voltage is greater than 6V so as to start up the controller. The load should be DC applicant wi

12 Step 1: Wiring The recommended connection order has been provided as Figure3-2 indicated. Be sure the positive and negative polarity is correct and

13 4 Operation 4.1 Battery Charging Information Figure 4-1 PWM Charging mode ·Bulk Charge In this stage, the battery voltage has not yet reached

14 ·Float Charge After the battery is fully charged in Boost voltage stage, the controller reduces the battery voltage to Float voltage set point. Whe

15 NOTE: Equipment damage! Equalization may increase battery voltage to the level damaging to sensitive DC loads. Ensure that all load allowable input

16 4.2 LED Indicators Charging indicator Battery indicator Figure 4-2 LED indicators  Charging status indicator GREEN ON w

17 Charging Status LED indicator Table 4-1 Color Indicator Charging Status Green On Sol

18 Load status LED indicator Table 4-3 Color LED digital tube Load status R

19 3. Test mode This mode is the same as Dusk to Dawn. But there is no 10 minutes delay when controller recognizes the starting

20 Load work mode Table 4-4 Work mode 8H 4H 2H 1H Dusk to Daw

21 Load will be on for 10 hours after 10 minutes delay since sunset ○ × ○ × Load will be on for 11 hours after 10 minutes delay since sunset ○ × ○

22 5 Protection, Troubleshooting and Maintenance 5.1 Protection ·Load Overload If the load current exceeds the maximum load current rating, the cont

23 5.2 Troubleshooting Trouble Shooting Table 5-1 Faults Po

24 8H、4H、2H、1H Red LED indicator flashing together Over load or short circuit Overload: Please reduce the load and press the button once, the

25 5.3 Maintenance The following inspections and maintenance tasks are recommended at least two times per year for best controller performance.  Ch

LS0512R —— Solar Light Controller Nominal system voltage 12VDC Maximum PV input voltage 35V Nomin

26  Confirm that all the terminals have no corrosion, insulation damaged, high temperature or burnt/discolored sign, tighten terminal screws to the s

27 • Claim procedure: Before requesting warranty service, check the Operation Manual to be certain that there is a problem with the controller. Return

28 7 Technical specifications Electrical Parameters Table 7-1 Description

29 Temperature Compensation Coefficient Table7-3 Description Parameter Temperature Compensation Coeff

30 Battery Voltage Parameters (temperature at 25℃) Table 7-4 Charging Parameters Battery charging setting Sealed Over Vol

31 Environmental parameters Table 7-5 Environmental parameters Parameter Working

Dimensions 25(0.98) 97(3.82) 86(3.39) 44(1.73) 66(2.6) mm(inches)

Version number: V6.0

Contents 1 Important Safety Information ... 1 2 General Information ...

BEIJING EPSOLAR TECHNOLOGY CO., LTD. Tel：010-82894112 / 82894962 Fax：010-82894882 E-mail：[email protected] Website: www.epsolarpv.com

1 1 Important Safety Information Save These Instructions This manual contains important safety, installation and operating instructions. The following

2 General Safety Information  Read all of the instructions and cautions in the manual before beginning installation.  There are no user serviceable

3 2 General Information 2.1 Product Overview Thank you for selecting LandStar series solar light controller that adopts the most advanced digital te

4 The controller is for off-grid solar system, especially in solar light system, and protects the battery from being over charged by the solar module

5 2.2 Product Features Figure 2-1 LandStar characteristics 1 – Charging status LED indicator An LED indicator that shows charging status and a